Tapco Blend 16 Instrukcja Użytkownika

#MFOE#MFOEowner’s manual16-CHANNEL 4-BUS MIXER w/ ONBOARD EFFECTS

108. MID FREQ EQThis adjusts the frequency of the MID EQ (9) control from 100 Hz to 8 kHz. This gives you great flexibility in shaping your sound. List

11For an example, suppose your band is performing on stage, and you hear something unusual (well, more unusual than normal). Without interrupting thei

12AUX SENDS and RETURNS22. AUX 1 SEND MON OUTPUT To create a stage monitor mix, connect this 1/4" TRS output to the input of your stage monitor a

13UUMAXPHONESLAMPBYPASSEQ INFX OLMAIN MIXAUX1(MON)POWERPHANTOM 48V1MAINMIXSUB2SUB3SUB4SUBSUB ASSIGNTO MAIN MIX MASTER AUX SENDCTRL RMPHONE

14INTERNAL EFFECTS The internal effects circuit receives mono signals from the AUX 2 FX bus, and it outputs stereo signals onto the main mix buses. It

1538. USB OUTPUT: MAIN MIX/SUBS 1-2This switch allows you to choose if the main mix or if subgroups 1 and 2, are sent out of the mixer’s USB (62) outp

16amplifiers clip at about +10 dB, and some recorders aren’t so forgiving either. For best real-world results, try to keep your peaks between 0 dB and

17REAR PANEL FEATURES 53. POWER SWITCHPush the top of the switch labeled “ON” to turn the mixer on; you should see the POWER LED (27) glow with happin

18Appendix A: Using the Blend 16At first glance, the controls on the front panel of the Blend 16 may seem more at home in a space movie, right next to

19Three controls configure how the USB connection will work in different scenarios: USB Source switch: This lets you choose whether your computer is fe

2SAFETY INSTRUCTIONS1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this appa

20Studio: Direct MonitoringConfiguration: 1. Connect your mics and instruments to the mixer’s inputs (leave channels 15-16 unused).2. Connect your am

21Appendix B: Connections XLR ConnectorsChannels 1 and 2 use 3-pin female XLR connectors on the MIC inputs. They are wired as follows, according to st

22Appendix C: Specifications Frequency ResponseMic Input to any Output (Trim at 0 dB): +0, –1 dB, 20 Hz to 20 kHz –3 dB,

23Physical Dimensions and WeightHeight: Back: 5.0” (127 mm) Front: 2.5” (64 mm)Width: 18.5” (469 mm)Depth: 16.6” (422 mm)Weight: 11.

24 Block Diagram This shows an outline of the strange goings on inside the mixer.LRLR1234AUX 1AUX 2SOLOLOGICSUBLR1234CONTROLROOM LEVELMAINFADEREQMAIN

25Appendix D: Service InformationNo Audio into your Computer:• Confirm the mixer is receiving mic or instrument input signals.• Make sure you have se

26No Communication with the mixer:• The PC driver may not be installed correctly. Make sure your computer meets the system requirements. Uninstall th

27TAPCO LIMITED WARRANTYA. LOUD Technologies Inc. warrants all materials, workmanship and proper operation of this TAPCO product for a period of one

#MFOE#MFOEowner’s manual16-CHANNEL 4-BUS MIXER w/ ONBOARD EFFECTS

Part No. SW0426 Rev. A 08/2006©2006 LOUD Technologies Inc. All Rights Reserved.3What me, read a manual?Before you begin, please make sure that you r

4Getting StartedThe following steps will help you set up your mixer, and get the levels and adjustments just right. Please follow the instructions in

59. Now that you have a rough mix going, you may need to readjust the MAIN MIX FADER to a comfortable listening level. The meters should indicate by

6Here’s a quick glance at all the features packed into this mixer: 8 mono mic/line channels, with:• XLR microphone input jack • 1/4" TRS instr

7LEFTRIGHT 1234SUB OUTSMAIN INSERTLEFTBAL/UNBAL BAL/UNBALTIP SEND / RING RETURNRIGHTCONTROL RM OUTUSB IN/OUTMAIN OUTRIGHT LEFTAUXSENDSLINEINPUTLRBALOR

8LEFTRIGHT 1234SUB OUTSMAIN INSERTLEFTBAL/UNBAL BAL/UNBALTIP SEND / RING RETURNRIGHTCONTROL RM OUTUSB IN/OUTMAIN OUTRIGHT LEFTAUXSENDSLINEINPUTLRBALOR

9Blend 16 Features MONO CHANNELSMono channels 1 to 8 allow adjustment of EQ, Pan, and Level for mono signals. The output from each channel strip can b